View AD8120_4810211.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Triple Skew-Compensating Video Delay Line with Analog and Digital Control AD8120
FEATURES
Corrects for unshielded twisted pair (UTP) cable skew Delay of up to 50 ns per channel High speed 200 MHz BW @ VOUT = 1.4 V p-p and 0 ns delay 150 MHz BW @ VOUT = 1.4 V p-p and 50 ns delay Excellent channel-to-channel matching 30 mV offset matching RTI 0.8% gain matching Low output offset 30 mV RTI No external circuitry required to correct for offsets Independent red, green, and blue delay controls Drives 4 double-terminated video loads Digital and analog delay control 6-bit SPI bus I2C bus Analog voltage control Fixed gain of 2 Low noise High differential input impedance: 500 k 32-lead, 5 mm x 5 mm LFCSP
GENERAL DESCRIPTION
The AD8120 is a triple broadband skew-compensating delay line that corrects for time mismatch between video signals incurred by transmission in unshielded twisted pairs of Category 5 and Category 6 type cables. Skew between the individual pairs exists in most types of multipair UTP cables due to the different twist rates that are used for each pair to minimize crosstalk between pairs. For this reason, some pairs are longer than others, and in long cables, the difference in propagation time between two pairs can be well into the tens of nanoseconds. The AD8120 contains three delay paths that provide broadband delays up to 50 ns, in 0.8 ns increments, using 64 digital control steps or analog control adjustment. The delay technique used in the AD8120 minimizes noise and offset at the outputs. The bandwidth of the AD8120 ranges from 150 MHz to 200 MHz, depending on the delay setting. This wide bandwidth makes the AD8120 ideal for use in applications that receive high resolution video over UTP cables. The logic circuitry of the AD8120 provides individual delay controls for each channel. The delay times are set independently using a standard 4-wire SPI bus or a standard I2C bus, or by applying analog control voltages to the VCR, VCG, and VCB pins. Analog control offers a simple solution for systems that do not have digital control available. The AD8120 is designed to be used with the AD8123 triple UTP equalizer in video over UTP applications, but it can also be used in other applications where similar controllable broadband delays are required. The AD8120 is available in a 5 mm x 5 mm, 32-lead LFCSP and is rated to operate over the industrial temperature range of -40C to +85C.
APPLICATIONS
Keyboard-video-mouse (KVM) Digital signage RGB video over UTP cable Professional video projection and distribution HD video Security video General broadband delay lines
FUNCTIONAL BLOCK DIAGRAM
R d
G
d
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2009 Analog Devices, Inc. All rights reserved.
07839-001
B
d
AD8120 TABLE OF CONTENTS
Features .............................................................................................. 1 Applications ....................................................................................... 1 General Description ......................................................................... 1 Functional Block Diagram .............................................................. 1 Revision History ............................................................................... 2 Specifications..................................................................................... 3 Absolute Maximum Ratings............................................................ 5 Thermal Resistance ...................................................................... 5 Maximum Power Dissipation ..................................................... 5 ESD Caution .................................................................................. 5 Pin Configuration and Function Descriptions ............................. 6 Typical Performance Characteristics ..............................................7 Theory of Operation .........................................................................9 Controlling the Delay ...................................................................9 Setting the Delay............................................................................9 Analog Control ........................................................................... 10 Digital Control ............................................................................ 10 Applications Information .............................................................. 14 Typical Application Circuit for the AD8123 and AD8120 ... 14 Outline Dimensions ....................................................................... 16 Ordering Guide .......................................................................... 16
REVISION HISTORY
7/09--Revision 0: Initial Version
Rev. 0 | Page 2 of 16
AD8120 SPECIFICATIONS
TA = 25C, VS = 5 V, RL = 150 , 10% to 90% input rise/fall time (tR/tF) = 4 ns, unless otherwise noted. Table 1.
Parameter DELAY CHARACTERISTICS Total Adjustable Delay Range Delay Resolution Propagation Delay Channel-to-Channel Delay Error DYNAMIC PERFORMANCE -3 dB Video Signal Bandwidth -3 dB Small-Signal Bandwidth 0.1 dB Video Signal Flatness 10% to 90% Rise/Fall Time Settling Time to 1% Slew Rate Test Conditions/Comments Delay Code 63 to Delay Code 0 Monotonic, 1 LSB Delay = 0 ns All channels at maximum delay VOUT = 1.4 V p-p, delay = 0 ns VOUT = 1.4 V p-p, delay = 50 ns VOUT = 0.2 V p-p, delay = 0 ns VOUT = 0.2 V p-p, delay = 50 ns VOUT = 1.4 V p-p, delay = 0 ns VOUT = 1.4 V p-p, delay = 50 ns VOUT = 1.4 V step, delay = 0 ns VOUT = 1.4 V step, delay = 50 ns VOUT = 1.4 V step, delay = 0 ns VOUT = 1.4 V step, delay = 50 ns VOUT = 1.4 V step, delay = 0 ns, rising edge VOUT = 1.4 V step, delay = 0 ns, falling edge VOUT = 1.4 V step, delay = 50 ns, rising edge VOUT = 1.4 V step, delay = 50 ns, falling edge VOUT = 1.4 V step, delay = 0 ns VOUT = 1.4 V step, delay = 50 ns 0 ns to 50 ns delay Over all codes, among all channels Measured on G with R and B driven at 1 MHz, VOUT = 1.4 V p-p, delay = 0 ns RIN, GIN, BIN Min Typ 50 0.8 4.9 0.4 200 150 165 140 27 35 2.5/3 3/4.2 8 18 550 540 510 360 1 20 2.01 0.8 -80 Max Unit ns ns ns ns MHz MHz MHz MHz MHz MHz ns ns ns ns V/s V/s V/s V/s % % V/V % dB
Overshoot Gain Channel-to-Channel Gain Matching Hostile Crosstalk VIDEO INPUT CHARACTERISTICS Input Bias Current Input Capacitance Input Resistance VIDEO OUTPUT CHARACTERISTICS Output Voltage Swing Output Current Integrated Output Noise
1.95
2.06 3
0.8 1 500 ROUT, GOUT, BOUT 3.25 50 100 kHz to 160 MHz Delay = 0 ns Delay = 50 ns Over all codes Over all codes, among all channels PD high, at 20 MHz VCR, VCG, VCB VCR, VCG, VCB VCR, VCG, VCB to move one delay LSB 1 4 0 30 1.5 1 0 28
1.5
A pF k V mA mV rms mV rms mV mV A V mV
Output Offset Voltage (RTI) Channel-to-Channel Output Offset Voltage Matching (RTI) Output Impedance ANALOG CONTROL INPUT CHARACTERISTICS Input Bias Current Operating Range Delay Voltage Step Size in Linear Range
-30
+30
2
Rev. 0 | Page 3 of 16
AD8120
Parameter DIGITAL CONTROL INPUT CHARACTERISTICS Input Bias Current Input High Voltage Input Low Voltage Output High Voltage Output Low Voltage SPI TIMING CHARACTERISTICS Clock Frequency CS Setup Time, t1 Clock Pulse High, t2 Clock Pulse Low, t3 Data Setup Time, t4 Data Hold Time, t5 CS Hold Time, t6 I2C TIMING CHARACTERISTICS Clock Frequency Start Setup Time, t1 Clock Pulse High, t2 Clock Pulse Low, t3 Data Setup Time, t4 Data Hold Time, t5 Hold Time, t6 POWER SUPPLY Positive Supply Range Negative Supply Range Positive Quiescent Current Test Conditions/Comments SDO/SDA, SCK/SCL, SDI/A1, CS/A0, SER_SEL, MODE Min Typ Max Unit
2 2.6 0.6 4.5 0.6 SCK CS to SCK SCK SCK SDI to SCK SDI to SCK SCK to CS SCL SDA to SCL SCL SCL SDA (input) to SCL SDA (input) to SCL SCL to SDA 10 5 50 50 5 5 5 100 10 5 5 100 100 10 4.5 -5.5 Delay = 0 ns Delay = 50 ns Powered down, PD low Delay = 0 ns Delay = 50 ns Powered down, PD low TMIN to TMAX, delay = 0 ns TMIN to TMAX, delay = 50 ns RL = 150 , delay = 50 ns RL = 150 , delay = 50 ns 44 114 4 37 108 0.5 0.13 0.36 56 44 5.5 -4.5
A V V V V MHz ns ns ns ns ns ns kHz ns s s ns ns ns V V mA mA mA mA mA mA mA/C mA/C dB dB
Negative Quiescent Current
Quiescent Current Drift +PSRR -PSRR
Rev. 0 | Page 4 of 16
AD8120 ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter Supply Voltage Internal Power Dissipation 32-Lead LFCSP at TA = 25C Input Voltage Storage Temperature Range Operating Temperature Range Lead Temperature (Soldering 10 sec) Junction Temperature Rating 6 V 3.5 W VS- - 0.3 V to VS+ + 0.3 V -65C to +125C -40C to +85C 300C 150C
The power dissipated in the package (PD) is the sum of the quiescent power dissipation and the power dissipated in the package due to the load drive for all outputs. The quiescent power dissipation is the voltage between the supply pins (VS+ and VS-) times the quiescent current (IS). Power dissipated due to load drive depends upon the particular application. It is calculated by multiplying the load current by the associated voltage drop across the device. RMS voltages and currents must be used in these calculations. Airflow increases heat dissipation by reducing JA. To ensure optimal thermal performance, the exposed paddle must be in an optimized thermal connection with an external plane layer.
6
MAXIMUM POWER DISSIPATION (W)
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
5
4
THERMAL RESISTANCE
JA is specified for the worst-case conditions, that is, for a device soldered in a circuit board for surface-mount packages. Table 3. Thermal Resistance
Package Type 5 mm x 5 mm, 32-Lead LFCSP JA 36 JC 2 Unit C/W
3
2
1
-20
0 20 40 60 AMBIENT TEMPERATURE (C)
80
MAXIMUM POWER DISSIPATION
The maximum safe power dissipation in the AD8120 package is limited by its junction temperature. The maximum safe junction temperature for plastic encapsulated devices, as determined by the glass transition temperature of the plastic, is approximately 150C. Temporarily exceeding this limit may cause a shift in the parametric performance due to a change in the stresses exerted on the die by the package. Exceeding a junction temperature of 175C for an extended period can result in device failure.
Figure 2. Maximum Power Dissipation vs. Ambient Temperature on a JEDEC Standard 4-Layer Board
ESD CAUTION
Rev. 0 | Page 5 of 16
07839-002
0 -40
AD8120 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
30 SCK/SCL 29 SDI/A1 31 CS/A0 32 GND 25 VS+ 27 GIN 28 BIN 26 RIN
GND
1
DIGITAL CONTROL
24 GND
DNC DNC PD
3 4 5
AD8120
ANALOG CONTROL
SDO/SDA 2
23 VCR 22 VCG 21 VCB 20 VREF 19 DNC 18 GND 17 VS+
B d
G d
R d
SER_SEL 6 MODE GND 7 8
GND 10
GND 12
GOUT 13
GND 14
ROUT 15
TOP VIEW (Not to Scale) NOTES 1. DNC = DO NOT CONNECT. 2. EXPOSED PAD ON UNDERSIDE OF DEVICE MUST BE CONNECTED TO PCB PLANE.
BOUT 11
VS+ 16
VS-
9
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No. 1, 8, 10, 12, 14, 18, 24, 32 2 3, 4, 19 5 6 7 9 11 13 15 16, 17, 25 20 21 22 23 26 27 28 29 30 31 Exposed Pad Mnemonic GND SDO/SDA DNC PD SER_SEL MODE VS- BOUT GOUT ROUT VS+ VREF VCB VCG VCR RIN GIN BIN SDI/A1 SCK/SCL CS/A0 EP Description Ground. Serial Data Output for SPI Bus/Bidirectional Serial Data Line for I2C Bus. Do Not Connect. Power-Down. Selection of SPI Serial Bus or I2C Serial Bus (I2C = 0, SPI = 1). Selection of Analog Control Mode or Digital Control Mode (Digital = 0, Analog = 1). Negative Power Supply. Connect to -5 V. Blue Channel Video Output. Green Channel Video Output. Red Channel Video Output. Positive Power Supply. Connect to +5 V. Internal Reference Bypass. Connect a 0.01 F capacitor between this pin and GND. Analog Delay Control Voltage, Blue Channel. Analog Delay Control Voltage, Green Channel. Analog Delay Control Voltage, Red Channel. Red Channel Video Input. Green Channel Video Input. Blue Channel Video Input. Serial Data Input for SPI Bus/I2C Address Bit 1. Serial Clock for SPI Bus/Serial Clock for I2C Bus. Chip Select for SPI Bus/I2C Address Bit 0. Thermal Plane Connection. Connect the exposed pad on the underside of the AD8120 to any PCB plane with voltage between VS+ and VS-.
Rev. 0 | Page 6 of 16
07839-003
AD8120 TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25C, VS = 5 V, RL = 150 , 10% to 90% input rise/fall time (tR/tF) = 4 ns, unless otherwise noted.
4 2 0 -2 -4 -6 -8 -10
07839-010
6
DELAY CODE = 63 DELAY CODE = 33
DELAY CODE = 63 DELAY CODE = 33
4 2
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
DELAY CODE = 1 DELAY CODE = 2
0 -2 -4 -6 -8 -10 1 10 FREQUENCY (MHz) 100 1k
07839-011
DELAY CODE = 1
DELAY CODE = 2
-12 0.3
1
10 FREQUENCY (MHz)
100
1k
-12 0.3
Figure 4. Small-Signal Frequency Response for Various Delay Settings, VOUT = 0.2 V p-p
0.25
Figure 7. Video Signal Frequency Response for Various Delay Settings, VOUT = 1.4 V p-p
1.8
DELAY CODE = 0
DELAY CODE = 33 DELAY CODE = 63
1.6 1.4 1.2
AMPLITUDE (V)
DELAY CODE = 0
DELAY CODE = 33 DELAY CODE = 63
0.20
AMPLITUDE (V)
0.15
INPUT
1.0 0.8 0.6 0.4 0.2
INPUT
0.10
0.05
0 VS = 5V LOAD = 150
07839-012
0
20 40 60 TIME (ns) 80 100 120
0
0
20
40 60 TIME (ns)
80
100
120
Figure 5. Small-Signal Pulse Response for Various Delay Settings
Figure 8. Large-Signal Pulse Response for Various Delay Settings
50 45
1
12
22
DELAY CODE 33 44
120
55 62
110
QUIESCENT CURRENT (mA)
40
RELATIVE DELAY (ns)
100 THREE CHANNELS 90 80 TWO CHANNELS 70 60 ONE CHANNEL 50
07839-018
35 30 25 20 15 10 5 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 ANALOG CONTROL VOLTAGE (V) 1.8 2.0
07839-021
40
0
0
4
8
12 16 20 24 28 32 36 40 44 48 52 56 60 64 DELAY CODE
Figure 6. Relative Delay vs. Delay Code and Analog Control Voltage
Figure 9. Quiescent Current vs. Delay Code
Rev. 0 | Page 7 of 16
07839-013
-0.05 -20
-0.2 -20
VS = 5V, LOAD = 150
AD8120
0 20
POWER SUPPLY REJECTION RATIO (dB)
-10 -20
DRIVING R AND B SIMULTANEOUSLY MEASURING G
10 0 -10
OUTPUT LEVEL (dB)
-30 -40 -50 -60 -70 -80 -90
07839-014
DELAY CODE = 63
-20 -30 -40 -50 0.3 VS+ PSRR AT DELAY CODE 0 VS+ PSRR AT DELAY CODE 63 VS- PSRR AT DELAY CODE 0 VS- PSRR AT DELAY CODE 63 1 10 FREQUENCY (MHz) 100 1k
07839-015
07839-020 07839-017
DELAY CODE = 0
-100 0.3
1
10 FREQUENCY (MHz)
100
1k
Figure 10. Crosstalk on Green Channel vs. Frequency, VOUT = 1.4 V p-p
Figure 13. PSRR vs. Frequency
INTEGRATED OUTPUT VOLTAGE NOISE (mV rms)
10k
OUTPUT VOLTAGE NOISE DENSITY (nV/ Hz)
5
4
1k
DELAY CODE = 63
3
2
100
DELAY CODE = 0
1
07839-016
10 10
0
100
1k
10k 100k 1M FREQUENCY (Hz)
10M
100M
1G
0
4
8
12 16 20 24 28 32 36 40 44 48 52 56 60 64 DELAY CODE
Figure 11. Output Voltage Noise Density vs. Frequency
Figure 14. Integrated Output Voltage Noise vs. Delay Code, 100 kHz to 160 MHz
5 TYPICAL FALL TIME
QUIESCENT CURRENT (mA)
160 VS+, RGB DELAY CODE 63 140 120 100 80 60 40 20
07839-019
4 RISE/FALL TIME (ns)
VS+, RG DELAY CODE 63, B DELAY CODE 0 VS+, R DELAY CODE 63, GB DELAY CODE 0
3 TYPICAL RISE TIME 2
1
VS+, DISABLED
VS+, RGB DELAY CODE 0
0
0
4
8
12 16 20 24 28 32 36 40 44 48 52 56 60 64 DELAY CODE
0 -40 -30 -20 -10
0
10 20 30 40 50 TEMPERATURE (C)
60
70
80
90
Figure 12. 10% to 90% Rise/Fall Time vs. Delay Code, VOUT = 1.4 V p-p, VIN Rise/Fall = 2 ns
Figure 15. Quiescent Current vs. Temperature
Rev. 0 | Page 8 of 16
AD8120 THEORY OF OPERATION
The AD8120 is a triple, digitally controlled analog delay line, optimized for correcting delay skew between individual channels in common wired communication media such as unshielded twisted pair (UTP), shielded twisted pair (STP), and coaxial cables. In these applications, the AD8120 is used to time-align three video signals, usually RGB or YPbPr, that arrive at a receiver at different times due to variations in total delay per channel. Although its primary application is analog video, the AD8120 can be applied in other systems that require variable analog delays up to 50 ns with 0.8 ns resolution. The three channels consist of cascaded delay sections that are switched in such a way as to provide a total of 50 ns total delay difference between channels with 0.8 ns resolution. A fixed propagation delay is common to all channels, where the associated delay is set to 0. Therefore, the delay setting for a given channel is a measure of the relative delay among the channels, rather than an absolute delay. There are three options for controlling the delay: serial peripheral interface (SPI) serial bus, I2C serial bus, and analog control voltage. Two pins select the type of control: the MODE pin selects analog or digital control, and the SER_SEL pin selects the SPI or I2C serial bus (see Table 5). Table 5. Modes of Control
PD (Pin 5) 0 1 1 1 MODE (Pin 7) X 0 0 1 SER_SEL (Pin 6) X 0 1 X Control Type Power-down I2C control SPI control Analog control
A delay code is assigned to each quantization level, ranging from 0 to 63 in decimal format. The means of control (analog, SPI, or I2C) is selected by applying the appropriate logic levels to the MODE and SER_SEL inputs (see Table 5). All three channels must use the same delay control option in a given application. It is important to note that in skew correction applications, the metric is the relative delay between channels, not the absolute delay. Each channel of the AD8120 exhibits a constant delay at its zero delay setting, referred to as its propagation delay. This propagation delay is well matched between the channels and is subtracted out when performing skew correction. The delay codes, therefore, ignore the constant propagation delay and refer only to adjustable delay beyond the propagation delay. Delay can be calculated by multiplying the delay code by 0.8 ns. For example, setting the red delay to 8 ns (delay code = 10), the green delay to 16 ns (delay code = 20), and the blue delay to 28 ns (delay code = 35) produces the following relative delays: green delayed by 8 ns relative to red, blue delayed by 20 ns relative to red, and blue delayed by 12 ns relative to green. If an application requires control of absolute delay, the propagation delay must be added to the delay corresponding to the associated delay code.
SETTING THE DELAY
In most video skew compensation applications, it is best to set the delay of the path with the longest delay to 0, and then to add delay to the other paths to match the longest delay. In this way, the bandwidth of each path is maximized, and the noise of each path is minimized. Figure 16 illustrates a case where a test step is applied simultaneously to each cable input, and the green cable delay is the longest.
RED CABLE OUTPUT
In analog control mode, three control voltages, VCR, VCG, and VCB, control the delay of each channel. These voltages are converted internally to digital codes with 0.8 ns steps. Each AD8120 channel has a fixed overall gain of 2 and can drive up to four double-terminated 75 cables or PCB traces. A power-down feature can shut down the AD8120 for power saving when not in use.
GREEN CABLE OUTPUT 28ns
07839-022
BLUE CABLE OUTPUT
CONTROLLING THE DELAY
The delay time of each of the three channels is controlled in one of three ways. One control option is the application of analog control voltages to the VCR, VCG, and VCB inputs. The other two control options are via the SPI or I2C serial digital bus. The delay is set in discrete amounts with a nominal resolution of 0.8 ns per quantization level (or LSB), even in the analog control mode.
40ns
Figure 16. Cable Delay Example
In the example in Figure 16, the AD8120 green delay should be set to 0. The AD8120 red delay is then set to the delay difference between the green and red outputs, or 40 ns. Finally, the AD8120 blue delay is set to the delay difference between the green and blue outputs, or 28 ns. Using the digital delay codes, green delay = 0, red delay = 50, and blue delay = 35.
Rev. 0 | Page 9 of 16
AD8120
ANALOG CONTROL
A number of video transmission systems do not have a microcontroller embedded or otherwise available to provide digital control. These systems require analog control. Potentiometer control is one of the most common ways to implement analog control (see Figure 25). To select analog control, set the MODE pin high. The AD8120 has one analog control input for each channel: VCR, VCG, and VCB. The maximum recommended control voltage range on these inputs is 0 V to 2.0 V, although the actual control range where delay changes take effect is smaller and lies within this larger range. An internal ADC converts the analog control voltages into binary delay codes; therefore, the analog control is discrete with nominally 0.8 ns resolution. Figure 6 illustrates the typical transfer characteristic between control voltage and delay code.
SPI Control
The SPI bus operates in full-duplex mode and consists of four digital lines: SDI, SDO, SCK, and CS. Table 7. AD8120 SPI Pin Descriptions
Pin No. 29 2 30 31 Pin Name SDI SDO SCK CS Description Serial data input, master out slave in (MOSI) Serial data output, master in slave out (MISO) Serial clock from master Chip select; active low
DIGITAL CONTROL
Set the MODE pin low to select digital control (SPI or I2C). Set the SER_SEL pin high to select SPI mode, or set the SER_SEL pin low to select I2C mode. Table 6 provides the bit values for reading and writing the red, green, and blue registers. Table 6. Read/Write Instruction and Color Registers
Operation Write Red Read Red Write Green Read Green Write Blue Read Blue R/W Bit 0 1 0 1 0 1 C1 Bit 0 0 0 0 1 1 C0 Bit 0 0 1 1 0 0
The AD8120 is programmed in SPI mode using a 2-byte sequence (see Table 8). Data is clocked into the SDI pin or clocked out of the SDO pin on the rising edge of the clock, MSB first. The first byte contains the read/write (R/W) instruction and the color register address (see Table 6). The second byte contains the delay code to write to the part (R/W = 0) or the stored delay code to read from the part (R/W = 1). Figure 17 shows how to write Delay Code 42 to the green register. Figure 18 shows how to read Delay Code 21 from the blue register.
Table 8. SPI 2-Byte Sequence
Byte 1 (R/W Bit and Color Register) SDI SDO Bit 7 R/W X Bit 6 0 X Bit 5 0 X Bit 4 0 X Bit 3 0 X Bit 2 0 X Bit 1 C1 X Bit 0 C0 X Bit 7 X X Bit 6 X X Bit 5 D5 D5 Byte 2 (Data) Bit 4 D4 D4 Bit 3 D3 D3 Bit 2 D2 D2 Bit 1 D1 D1 Bit 0 D0 D0
Rev. 0 | Page 10 of 16
AD8120
CS
SCK
SDI
0
0
0
0
0
0
0
1
X
X
1
0
1
0
1
0
SDO
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Figure 17. Setting the Green Register to Delay Code 42 Using SPI
CS
SCK
SDI
1
0
0
0
0
0
1
0
X
X
X
X
X
X
X
X
SDO
X START
X
X
X
X
X
X
X
X
X
0
1
0 BYTE 2 DATA
1
0
1 STOP
Figure 18. Reading Delay Code 21 from the Blue Register Using SPI
Rev. 0 | Page 11 of 16
07839-026
BYTE 1 R/W BIT AND COLOR REGISTER
07839-025
START
BYTE 1 R/W BIT AND COLOR REGISTER
BYTE 2 DATA
STOP
AD8120
I2C Control
The I C interface of the AD8120 is a 2-wire interface consisting of a clock input and a bidirectional data line. The AD8120 drives the SDA line either to acknowledge the master (ACK) or to send data during a read operation. The SDA pin for the I2C port is open drain and requires a 10 k pull-up resistor. Table 9. AD8120 I2C Pin Descriptions
Pin No. 2 30 29 31 Pin Name SDA SCL A1 A0 Description Serial data input/output Serial clock input I2C Address Bit A1 I2C Address Bit A0
2
Table 10. I2C Addresses
A1 Pin 0 0 1 1 A0 Pin 0 1 0 1 I2C Address 0x38 0x39 0x3A 0x3B
In I2C mode, the AD8120 is programmed with a 3-byte sequence for a write operation (see Figure 19) and a 4-byte sequence for a read operation (see Figure 20). The first byte contains the 7-bit device address and the R/W instruction bit. The second byte contains the color register. In write mode, the third byte contains the delay code. In read mode, the third byte contains the device address, and the fourth byte contains the stored delay code.
The AD8120 address consists of a built-in address of 0x38 and the two address pins, A0 and A1. The two address pins enable up to four AD8120 devices to be used in a system (see Table 10). Both address pins must be terminated (high or low) for the AD8120 I2C interface to operate properly.
1 SCL R/W 9
1
9
SDA START BY MASTER
0
1
1
1
0
A1
A0
0 ACK BY AD8120
0
0
0
0
0
0
C1
C0 ACK BY AD8120
BYTE 1 I2C ADDRESS 1 SCL (CONTINUED)
BYTE 2 COLOR REGISTER 9
SDA (CONTINUED)
X
X
D5
D4
D3
D2
D1
D0
07839-023
BYTE 3 DELAY DATA CODE
ACK BY AD8120
STOP BY MASTER
Figure 19. I2C Write Sequence
1 SCL
R/W
9
1
9
SDA START BY MASTER
0
1
1
1
0
A1
A0
0 ACK BY AD8120
0
0
0
0
0
0
C1
C0 ACK BY AD8120
BYTE 1 I2C ADDRESS 1 SCL R/W 9 1
BYTE 2 COLOR REGISTER 9
SDA START BY MASTER
0
1
1
1
0
A1
A0
1 ACK BY AD8120
X
X
D5
D4
D3
D2
D1
D0 NO ACK BY AD8120 STOP BY MASTER
BYTE 3 I2C ADDRESS
BYTE 4 DATA BYTE FROM AD8120
Figure 20. I2C Read Sequence
Rev. 0 | Page 12 of 16
07839-024
AD8120
SPI Timing
Figure 21 shows the SPI 2-byte timing sequence. Table 11 lists the timing parameters for SPI.
CS
I2C Timing
Figure 23 shows the I2C 3-byte timing sequence. Table 12 lists the timing parameters for I2C.
A1 A0 R/W ACK C1 C0 ACK D5 D4 D3 D2 D1 D0 ACK
SCK
07839-005
SDA
01110
000000
XX
SDI/SDO
0
0
0
0
0
C1 C0
X
X
D5 D4 D3 D2 D1 D0
SCL
Figure 21. SPI 2-Byte Timing Sequence
t1
CS SCK SDI
Figure 23. I2C 3-Byte Timing Sequence
t6
t4
t2
R/W
t3 t4 t5
D1 D0
07839-006
SDA SCL
t1
t5
t6
Figure 22. SPI Timing Diagram
Figure 24. I2C Timing Diagram
Table 11. SPI Timing Parameters
Parameter t1 t2 t3 t4 t5 t6 Description Setup time, CS to SCK Clock pulse high, SCK Clock pulse low, SCK Setup time, SDI to SCK Hold time, SDI to SCK Hold time, SCK to CS
Table 12. I2C Timing Parameters
Parameter t1 t2 t3 t4 t5 t6 Description Setup time, SDA to SCL Clock pulse high, SCL Clock pulse low, SCL Setup time, SDA (input) to SCL Hold time, SDA (input) to SCL Hold time, SCL to SDA
Rev. 0 | Page 13 of 16
07839-008
t2 t 3
07839-007
R/W
AD8120 APPLICATIONS INFORMATION
Most twisted pair (TP) cables used for video transmission are designed for data communication and typically contain four individual TP channels. Minimization of crosstalk between pairs is of paramount importance in data communication applications. This is accomplished by varying the twist rates (twists per unit length) of each pair. For a given cable length, signals traveling on pairs with relatively high twist rates have longer distances to traverse than signals traveling on pairs with relatively low twist rates. The longer relative distances translate into longer relative delays and, similarly, the shorter relative distances translate into shorter relative delays. The delay of any TP channel is not flat over frequency, and an equalizer is generally used at the receiver to produce an approximately flat delay vs. frequency characteristic as well as an approximately flat frequency response magnitude over the bandwidth of interest. The term "group delay" is often used in the delay vs. frequency context. When the group delay and the magnitude response have been corrected to the best possible degree at the receiver, the remaining signals are close approximations to those sent at the transmit end of the cable, but with different delays with respect to the signals sent at the transmit end. The signals, therefore, manifest different delays relative to each other. The relative delay difference between any two equalized signals at the receiver is defined as delay skew, or simply skew, and is measured in units of time. Some bundled coaxial cables also exhibit delay skew between channels; these skew levels are typically much smaller than those encountered among similar length TP channels. The AD8120 can be used with RGB and YPbPr, as well as other video formats. Typically, three video component signals are transmitted over the TP cables, with each component carried on a pair. For example, with RGB video signals, the red, green, and blue signals are each transmitted over one pair. If these signals are carried over a cable with skew larger than a quarter of a pixel time and are displayed on a video monitor, the three colors will not be properly aligned and the skew will be visible at the vertical edges of objects displayed on the monitor. For fractional pixel time skew levels, a rainbow-like effect appears at the vertical edges of the objects; for skew levels longer than a pixel time, vertical lines are visible on the vertical edges of objects. The vertical lines are due to one color arriving earlier or later than the others. The best way to observe skew is to view an object against a black background. The AD8120 is a triple adjustable delay line, and its primary application is to realign the received, equalized video components. The pixel time of UXGA video with a refresh rate of 60 Hz is approximately 6.2 ns. In this case, the 0.8 ns delay resolution of the AD8120 represents approximately 13% of a pixel time.
TYPICAL APPLICATION CIRCUIT FOR THE AD8123 AND AD8120
Figure 25 illustrates a complete receiver application circuit using sync-on common mode; this circuit comprises the AD8123 triple equalizer and the AD8120. The circuit receives balanced RGB video signals over TP cable, performs cable equalization and skew correction, and directly drives 75 coaxial cable. The 6 dB voltage gain in the AD8120 compensates for the 6 dB double termination loss incurred driving the coaxial cable. The low-pass filter is optimized for short distances. Refer to the AD8123 data sheet for details regarding the sync encoding and decoding. The filter between the AD8123 and the AD8120 is a three-pole low-pass filter (LPF) with a cutoff frequency of approximately 148 MHz; the LPF is included to provide high frequency noise reduction. The filter shown in the application circuit performs well for short to medium length cables. Note that the 1 pF capacitance of each AD8120 input is added to each filter capacitor that is connected to each AD8120 input. Thus, for the filter shown, the actual filter capacitance at each AD8120 input is 16 pF. For longer cables, where much greater high frequency gain is required from the AD8123, it may be desirable to scale the LPF bandwidth back to provide greater noise reduction. This can be done by simply scaling the inductor and capacitor values by the ratio of the existing cutoff frequency of 140 MHz to the desired new cutoff frequency. For example, if a new cutoff frequency of 100 MHz is desired, the inductor and capacitor values are scaled by a factor of (140 MHz/100 MHz) = 1.4. This is summarized in Table 13. Table 13. Low-Pass Filter Component Selection for 100 MHz Cutoff
Original Value 5.6 pF 150 nH 15 pF + 1 pF1 = 16 pF
1
Scale Factor 1.4 1.4 1.4
New Value Ideal 7.8 pF 210 nH 22.4 pF - 1 pF1 = 21.4 pF
Standard 7.5 pF 220 nH 22 pF
Input capacitance of the AD8120.
Rev. 0 | Page 14 of 16
FAIR-RITE 2743021447 SERIAL BUS FOR DIGITAL CONTROL 0.1F 100 5 VS+_CMP 100 5.6pF 15pF 150nH 15pF 32 31 30 29 28 27 26 25 0.1F +5V 150nH POTENTIOMETERS FOR ANALOG CONTROL +5V 7.5k RED OUTR 18 +5V 7.5k GREEN +5V 7.5k BLUE 5.6pF 15pF 150nH 13 16 VS+ VS+ VS+ VS+ 19 29 36 0.1F 0.1F 0.1F 0.1F
+5V
4700pF
4700pF
0.1F
ANALOG CONTROL INPUTS
VS+ 26 VPEAK 27 VPOLE 25 VGAIN 23 VOFFSET
AD8123
100 5.6pF RED
POWER-DOWN CONTROL PD
28
49.9
31
BIN
GIN
RIN
CS/A0
SDI/A1
SCK/SCL
1 GND SDO/SDA DNC DNC PD 6 7 8 SER_SEL MODE GND GREEN OUTG 15 3 4 5 BLUE OUTB 12 CONTROL INPUTS 2
GND
49.9
VS+
RECEIVED RED VIDEO
32
5k GND VCR VCG 24 23 22
5k
5k
49.9
34
RECEIVED GREEN VIDEO
49.9
35
AD8120
EXPOSED PADDLE CONNECTED TO GND
VCB VREF DNC GND VS+
21 20 19 18 17 +5V 0.1F
VS-
GND
BOUT
GND
GOUT
GND
ROUT
BLUE CMV 2 1 OUTCMP1 4 49.9
1k
RED CMV OUTCMP2 VS- 14 0.1F 0.1F 0.1F 0.1F 17 22 33 0.1F VS- VS- VS- VS-_CMP 9
3
-5V 0.1F
9
10
11
12
13
14
15
16
VS+
07839-004
Figure 25. Typical Application Circuit
Rev. 0 | Page 15 of 16
GND 24, 39 2 VS- 11 6 49.9
49.9
37
RECEIVED BLUE VIDEO
49.9
38
1k
0.1F +5V 0.1F 75 75 75 RED OUT GREEN OUT BLUE OUT HSYNC OUT VSYNC OUT
8
GREEN CMV
475
7
47pF
47pF
0.1F
FAIR-RITE 2743021447
-5V
4700pF
4700pF
AD8120
AD8120 OUTLINE DIMENSIONS
5.00 BSC SQ 0.60 MAX 0.60 MAX
25 24 32 1
PIN 1 INDICATOR
PIN 1 INDICATOR TOP VIEW 4.75 BSC SQ
0.50 BSC
EXPOSED PAD (BOTTOM VIEW)
3.65 3.50 SQ 3.35
8
0.50 0.40 0.30 12 MAX
17 16
9
0.25 MIN 3.50 REF
0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM
1.00 0.85 0.80
COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2
Figure 26. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 5 mm x 5 mm Body, Very Thin Quad (CP-32-4) Dimensions shown in millimeters
ORDERING GUIDE
Model AD8120ACPZ-R2 1 AD8120ACPZ-R71 AD8120ACPZ-RL1
1
Temperature Range -40C to +85C -40C to +85C -40C to +85C
Package Description 32-Lead Lead Frame Chip Scale Package (LFCSP_VQ) 32-Lead Lead Frame Chip Scale Package (LFCSP_VQ) 32-Lead Lead Frame Chip Scale Package (LFCSP_VQ)
Z = RoHS Compliant Part.
(c)2009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D07839-0-7/09(0)
Rev. 0 | Page 16 of 16
100608-A
SEATING PLANE
0.30 0.23 0.18
0.20 REF
COPLANARITY 0.08
FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET.
Package Option CP-32-4 CP-32-4 CP-32-4

▲Up To Search▲

Price & Availability of AD8120

	To Download AD8120 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .